Jump to content

sylvain

Members
  • Posts

    158
  • Joined

  • Last visited

Profile Information

  • Location
    France

sylvain's Achievements

Certified R Fan

Certified R Fan (4/9)

0

Reputation

  1. Hi, Il go in Scottland for few days on monday, probably with my R. In France, fuel price is about 1.50€ per litter for unleaded 98RON octane rating. I can't find equivalent in UK, i found someting like: - Unleaded (whitch octane rate ?) at 134.37p (what does it mean ? It's pennys ? It's per Gallon or per litter ?). - LRP: what is it ? - Super: what is it ? - LPG: what is it ? Whitch on sould i use for my R (In France i only use 98 octane unleaded fuel) and how convert the price in €/litter ? Thanks for helping ! Other question: my front tyre are very used, i have two new RE050A at home, do UK garages accept fitting typres has been bought in other shop ?
  2. My DSG R, with MRC remap. At 5hz race GPS: - 0-100km/h: 4.6s - 0-200km/h: 19s
  3. This is an APR downpipe, about 2K£....Â
  4. Hi, We know that it's possible to completly swith off ESP on MY'2012, anyone here ask his dealer to know if it's possible on 2011 and 2010'MY (by reflash) ? Thanks.
  5. Many R DSG refash exists, all Scirocco cup's DSG include, and it's not a R32 map. Accordinf the gearbox is a DQ-250 model, the unit is the same on R32, TT, GTI... so the software upgrade is possible, there is no specific version for R model, only the checksum for reflashing ECU is different, so it's just a flash tool problem... (money problem for license propably).
  6. Without Downpipe, your HP gain is more near 0%
  7. Yes, if i asked that, it's because on the Milltek install guide, the shaft need to be remove, only for for removing stock DP (the Milltek DP is thinner than stock one). It's the same for S3 and TTS DP, shaft need to be removed.
  8. Rien n'a été enlevé Nothing was removed for the installation. I put the car on the ramps, the guy got under the car, took off the old exhaust after some pulling and grunting and WD40, slide the new exhaust in place and voilà ! I love you Milltek. >:-D Yes but do you have the Hi-Flow cat downpipe or only the cat-back exhaust ?
  9. Is the shaft to rear diff have been removed for downpipe installation ?
  10. Here dump and programming ECU is done with "CMD" flash tool. MAP tuning done with WinOLS. Both works fine for R (not the same ECU as GTI, R have the old Golf MKV ECU).
  11. Flash back the stock software and ask a payback money. Like me (i'm back on stock software after DSG issues and boost cuts), i think i will reflash DSG first and wait more time since Tuner have more experience on this Map.
  12. A R is passed on dyno here, with Octane 95: 252hp ! Same R with 98 after a full tank refill, 271hp
  13. Hi, here is the verdict: It's the DSG software making theses boost cut, each time the torque hit the 400nm limit, the torque immedialtly drop to 370nm in 200rpm only, and stay at this max limit. So the power is good: 322hp, but there is no more torque than stock until 5500rpm. And if you hit 410 or 420nm, torque is drop and you have a boost cut during 2 or 3 seconds at next shift up, whenever the rev. So my tuner repay me. For him and his relations (kemPower), it's due to 2011 DSG software, very different of 2010 one. Because the torque limiter remove has no effect. I've send an email to HPA Motorsports, for DSG remap, only few tuners can remap DSG software, i saw Revo too but don't know if they make 2011 DSG. Is some of you have already remap a 2011 R ? Can you post the curves, because only curves show the problem i have, the torque value can be 420nm, but it's only for 200-500rpm befor droped by security. Thanks.
×
×
  • Create New...