Jump to content

red4765

Members
  • Posts

    7
  • Joined

  • Last visited

Everything posted by red4765

  1. Finally I got the Koni FSD fitted. Here is what I think. My R came without the electronic damping control, and the ride on OEM suspension was just too harsh on the city roads (if you have been to Bangkok you would know). Now, with the Koni FSD. The ride over road cracks and small little bumps in the city improved so much. I would say at least 35-40% of the harshness and roadnoise were gone. The improvement in ride comfort not only improved at lower speed. At higher speed 40-60 mph, the little road imperfections were also well subdued. However, larger or deeper holes still hit hard and I can only feel sorry for the car. I guess with 35 series 19", no suspension in the world could do anything to dampen impact of >30mm deep holes at speed of 35+mph. You just have to watch out for those pot holes if you ride on low profile tires. Now, with the ride comfort much improved on the city roads, how does it perform on the highways or on tight windy roads? Before I say anything, I need to explain that after fitted, the FSD seems to have increased the ride height a little, by may be about 0.5-0.75 inches. The height increased might come down a little after the breakin, I'm not too sure. And although, I still have the stock springs, the change in ride height could mean that I should get the wheel allignment done again, which unfortunately I haven't done yet. This may have been the cause of why the road holding performance suffered slightly in my opinion. The car felt a tad taller and softer as a whole which is quite deceiving. On the turn in, the streeing felt a little too light, and the front wheels didn't pinch in to the line as well as it used to. It felt like the car has just a tiny bit more tendency to understeer, althought I didn't get the opprtunity to push it to the limit. Also, you have to understand that my car was fitted with both UNIBrace XD and UB, and usually the FW would hug the line pretty well and I could usually feel the weight transferred to the rear a little which I like more than with OEM setup. This however is gone for now. I have driven badly alligned cars before, and there is a good chance that the lighter and less responsive steering could be from the need to get the wheels readjusted again. I personally felt that the FSD should eventually outperform the stock in term of road holding. This is because, while the ride is softer over road imperfections, the body roll in tight turns or on highway (at 100+mph) was definitle less than the stocks. So I am quite convinced that with proper wheel settings, the FSD should provide perform better. Another interesting thing is that, while the ride is improved significatly, the well known creaking noise that usually come from the doors were not improve much. These sound which I think comes from the body flex and the badly designed door hinge and door seal rubber could not be resolved with better ride alone. I used to think that with softer ride these noises would be much less, I was wrong. In fact the UNBrace did much better in reducing these noises and also provided better ride comfort too. Who would have thought that stiffening up the body would be so effective at this? So, overall it is not conclusive yet how good the Koni FSD is in term of road holding performance. I'm not sure if I can give a definite answer to this because my H&R sport springs will arrive next week. And I will get the wheel allignment done only after the springs are fitted. I just couln't be bothered to get it done now just to find out how good the FSD is by itself, since I will have to do it again a couple days later. The only thing I can say is the ride quality is so much improved. It is so good that it allows me to stop thinking about alternative routes to avoid bad roads before I begin a journey. And by my experience today driving 100-120mph on the highway for 15-20mins, the car still had pretty good grip and the confidence is still there, even without the wheels allignment done yet. So far, I don't regret getting the FSD at all. It is a very good product, but how good I will only know next week. I will update again after the H&R springs are fitted and the wheels re-alligned (the H&R springs should bring the ride height back down near standard or slightly lower, they are .75" shorter and not much stiffer than stocks). Also to be fitted at the same time are the 5mm spacers. If I can get them all to create softer and quieter ride, at the same time as providing better grip and look, I'll be delighted.
  2. How much did you pay? What colour? Where are the LEDs made (China or Korea)? I just got mine fitted, LEDs from Korea are of better quality. I guess it's very cheap in my country. Somehow I'm not so happy with my color (brilliant white). I think I'm gonna try to find some red or blue LEDs... ;D
  3. Thanks for your advice. Â The FSD would probably provide some ride comfort. Â The only thing I'm worried about is if it would ruin the already great handling of OEM suspension. Â I will ask someone on MKV who is using the FSD.
  4. I've just ordered my K&N a few days ago, but I didn't go for the Panel Filter. Instead I ordered 57-0570 K&N 57i Induction Kit. It's not expensive, and I can't see why it should be any worst than Carbonio intake.
  5. I've got mind fitted. However, since it was done at the same time as my Stage 1 ECU upgrade I can't tell if it improve the performance. The problem is, I was later warned that the Forge Blow Off Valve allows some boost surge and can lead to Turbo damage. I don't know how true this is and whether I should have mine removed. Any experts here?
  6. I live in a city where normal roads are crappy; lots of cracks, potholes, uneven surfaces. The highways are alright. I usually spend 65% on normal roads, 35% on highways. At the moment the OEM setup feels very rough on normal road, but great handling on highways. I'm wondering what I would get if I replace the OEM with Koni FSD (shock absorbers only, with OEM springs) or KW Variant 3 Coilover (on softest setting). Would the Koni FSD provide better ride comfort in town? Would the handling suffer, or would it be better than OEM shock absorbers? I've heard the KW Variant 3 coilover, even on softest setting, is still very hard, is this true? Or would it be better than OEM in term of ride comfort, and handling. Price is not the subject here. (BTW, I'm also having UNIBrace XB and UB installed in a few weeks. According to Bruce, the improve rigidity of the chasis should improve ride quality somewhat as well as improving handling. As there will be less body deflection and the suspension can work more efficiently). Any advices is highly appreciated.
×
×
  • Create New...