Jump to content

merzdom

New Members
  • Posts

    11
  • Joined

  • Last visited

Everything posted by merzdom

  1. So, could I trouble anyone into checking to see if they have oil residue at the end of the PCV hose (where it attaches to the turbo inlet pipe)?
  2. Oh, it's definitely going into the shop as soon as I can get it there. I was curious to know if anyone else has experienced this, and whether or not the PCV valve hose (where it connects to the turbo inlet) should be leaking oil.
  3. Helloooo, I drive a '16 R (North American/direct-injected) which has the Racingline R600 intake, Racingline turbo inlet hose & pipe, APR intercooler, and APR downpipe installed. I am on APRs stage 2 ECU & TCU software. After installing the turbo inlet hose & pipe I noticed a persistent beeping/whistling sound at high engine speed/under hard acceleration. The noise is constant; in other words, it doesn't fluctuate with engine speed (it's either on or off). The car has 8500 miles on the odometer (13680km). Today, I noticed that there is a significant amount of oil around the end of the PCV hose (where it mates with the turbo inlet pipe). There is also dirt/oil residue on portions of the turbo inlet pipe. I'm assuming this isn't normal? Could this be related to the noise I'm hearing? Also, I get a stutter sound (like very quick bursts of pulsing air) under load at lower engine speeds when accelerating (especially in 3-6 gears). Any thoughts? All the best- James
  4. Thanks again for the direction. My sound happens a little later in the rev-band, and might be described as more harmonic (less whistle-y). Although, I'm only hearing it from the inside of the cabin so, who knows, maybe it is more like a whistle from outside. I'll have it diagnosed soon.
  5. One more question comment regarding this noise, do you have the snorkel drain plug attached? I installed the R600 before installing the VWR elbow and hose, but I tossed the snorkel while I was installing the elbow and hose (it wasn't staying put, and after a call to VWR/Racingline I was assured that the snorkel could be omitted without an adverse effect). I'm wondering if that open hole is creating the noise, like blowing across the opening of an empty beer bottle.
  6. Thanks for the feedback; I'll have it checked out soon as I'm having an intercooler installed in two weeks.
  7. I have the VWR/Racingline elbow (turbo inlet pipe), and turbo inlet hose. I have no complaints; both parts had great fit and finish. However, my car developed a strange sound directly after I installed them. Under hard acceleration, at or near full boost, I hear a distinct whistle/beep-like tone. It reminds me of a high pitched, miniature train whistle. Anyone else experience this??
  8. Yikes, now I'm worried. Time to make an appointment.
  9. I've considered installing the HPA dog bone mount, and I actually have an 034 billet insert sitting on my desk at the moment. Although, I was lead to believe (perhaps incorrectly) that a full engine mount kit was the better solution in the long run. Maybe I should rethink this.
  10. Hello! I own a 2016 Golf R (DSG, DCC) which has stage 2 APR ECU & TCU software installed. I'm running the stock 19" summer tires. There are no other modifications other than power mods (intake, turbo inlet pipe, downpipe). When I use launch control (with ESC completely disabled) or when I apply 100% throttle input in first gear, under less than ideal traction conditions (viz. wet roads, cold tires, etc.), I experience noticeable wheel hop (or rather, what I suspect to be wheel hop). There is a shudder/knock that repeats a few times before the car manages to "dig in" and go. Is this normal? It was my understanding that the current gen Haldex controller was rather quick about sending power to the rear wheels. I didn't experience wheel hop in my APR stage 2+ mk6 R, so I am a little curious. Any input would be much appreciated! All the best.
×
×
  • Create New...