Jump to content

Rxilher

New Members
  • Posts

    14
  • Joined

  • Last visited

Everything posted by Rxilher

  1. Nope. In the Golf (and most other current VW’s) there is a small reverse torx lock screw in each hinge (covered with a small black cap). When those are removed/loosened and the wiring harness is unplugged the door lifts right up without touching the hinge halves. There will probably be a tiny bit of marring on the torx screw, but the plastic cap covers it. My concern is that they use a proper door jack to assure they do not hit the door on the fender, A pillar, or lower door sill.
  2. Sadly....not really. It is hard to know for sure until it is fully removed, but there is a strong chance the part is defective. There is a slim possibility they were just not clipped properly or came un clipped at some point. The only thing you can do without removing the door (which is actually really easy thanks to VW’s design) is open the door fully and try to use your hand to press the rubber shield toward the front bumper. I used a light and carefully flexed the seal further away from the fender to identify where the fastening point was, then directed my forward pressure to that spot. I was able to get mine to seal and reseat. In my case the paint was already severely damaged and needed to be addressed. Keep in mind if you “fix” the issue, the dealer may do nothing. They should see it first.
  3. Well. Mine was fixed by a VW body shop. It turned out well, but only because I was very specific how I wanted it repaired. My fender seal was replaced (clip was broken). Door was removed (super easy). Edge was prepped and hand brushed with a pin-striping brush 2 coats of touch up, then door was remounted.
  4. They said, "it could have easily been popped out by user error while cleaning the car". Lol. Hence me getting a second opinion.
  5. On my end I was told by the dealer (at least one of the dealers) VWNA would not cover. I'm going to go to a different dealership and see if I can I get a different answer. As I have a huge distrust for nearly every body shop I will most likely try to get the dealer to cover a paint pen and a new seal. I've been plan to remove the door, touch it up, and replace the seal.
  6. Keep them coming fellas! I am loving the feedback....and of course knowing I am not the only one that is taken back with how freaking quiet it is. I was even thinking about exhaust just to break the silence (usually a good noisy intake is enough!)
  7. Hello all, As of about two weeks ago I am the proud owner of a 2017 MK7 golf R 6MT. I come from a very long history of turbo DSM cars. Cars running 14psi of boost stock that had turbo sounds 3x of the R. I know this may sound a little ridiculous, but I greatly miss the sound that came from those cars. I am holding off on doing a tune for right now because I haven't come to terms with potentially losing warranty coverage with such a modification. I just installed an APR turbo inlet pipe and an ECS Tuning turbo muffler delete. I have noted a very minimal change in spool noise, but so slight that I cannot justify the $ for these two parts. Does anyone have some recommendations? Insights? Maybe hard IC piping? Go Fast DVX? I turned of the Soundaktor because I want real noise
  8. Maybe I have them replace the seal and use a steady hand to touch up with OEM touch up paint?
  9. Unfortunately think that might be the only method. It is bare metal. VW has "certified" body shops.
  10. Dang! Yeah. It seems that no one noticed the fender seal/shroud was warped... inner clip broke. Causing the rub. Now my only hope is a body shop doesn't make it worse with bad paint work.
  11. Hi OP, Any updates? I think Inhave the same issue on my 2017. The fender seal seems to have come loose. The paint is worn off to the bare metal :-(.
  12. Rxilher

    Hello all!!

    Hi all, it has been years sincw I had a VW. Just picked up a CPO 2017 Golf R 6MT. GLAD TO BE BACK!
×
×
  • Create New...