ben120280
Members-
Posts
55 -
Joined
-
Last visited
Content Type
Profiles
Articles
Forums
Events
Store
Classifieds
Everything posted by ben120280
-
No idea what any of that meant to be honest! As long as they are better than the OE and dont turn to duct in 6 months from a 10mm drop, id be happy!
-
Other than the Eibach springs, I went full OE with shocks, top mounts, bearings and all sundry parts needed for a complete overhaul. Ive since been back to the garage and its 100% failed again for the OSF. They have offered to replace it again FOC under warranty but now thinking that some uprated top mounts may be the way to go..
-
Hi all... I've a 2016 R Estate that recently had an overhaul of its suspension (long story but a pot hole forced my hand) Anyway, I went for new OE shocks and top mounts all round and a set of Eibach springs... the smallest drop they offer so about 10mm I think. Almost instantly the NSF was creaking and knocking, the garage did mention it to me when I collected the car and told me to keep in touch if it doesn't stop. After about 2 months and no improvement, they replaced the top mount under warranty and it looked messed up (cant think of any technical way of saying it!) all in all, pleased with the service and everything else as things do happen. That was about 3 months ago and since its been fine but now the OSF has started knocking loudly and I suspect that's now also shot. The last time I ran a lowered car was about 20 years ago on a MK1 focus, dropped about 30mm and didn't have a single issue. I cant find anything on the net about OE top mounts failing after less than 5k miles. I will go back to the garage again to see what they say but if they havent fitted them correctly then dont really want to keep going back. Anyone have any experience or suggestions? Currently looking at replacing the top mounts for uprated ones if this is an issue.. Thanks
-
Finally had some time to put some bits on. Small changes but hopefully they start to make “Tabby” more of my own style.
-
Thanks Dustybones.... that’s actually a pretty good idea, if I cock it up I’ve only wasted time But if it goes ok... 💰 I shall keep you posted next week!
-
Good to know!!! Mrs was in bits! Anyone have and recommendations in Leicester?
-
Reap rays???? Re sprays... obviously 🤣
-
So the mrs reversed into a multi story car park support column today 🤦♂️ looks to be just bumper damage but as I haven’t damaged a car in 20 years I’ve no idea what’s possible with smart repairs, reap rays or replacements. anyone got any ideas🤷♂️
-
So bit of an update..... in my quest to validate the supplier, they have very kindly forwarded me to a website of a company that they supply the wheels to based in the USA. Anyone have any dealings with www.apexraceparts.com looks a nice site with lots of good info
-
Yea thats a better angle... nice and flush! Id probably only go a small drop if any as it is the family wagon.
-
Do you have ET45 front and rear without spacers in that shot? Looks very nice on the front but the rear might take another 5mm.. what are your thoughts? Might add that mine is an estate but assuming that it doesnt alter the clearance?
-
Yea its a fine balance between concave / dish and calliper clearance. There is actually a measurement on wheels called the X FACTOR, its the distance from the mounting fact to the inner face of the spokes... cant remember the distance from the center bore now though. This will basically tell you the level of clearance you can expect... trying to find an X factor for the Prets is proving hard so will have to get them off and measure up. Lockily this was my job for years and can calculate on paper offset and width differences with diagrams to scale 😎 These will also be stronger than the Prets so double bubble!
-
Yea the Bronze is 100% on my hit list for this wheel I think. I can spec any offset I want so currently trawling through all the posts to see what's best front and rear... seems 45 front and 35 rear at the moment. Ive looked online and seems the prets are 19x8 and about 10kg. As these are 8.5 width and wont need spacers there should be some overall saving? Latest info from the factory is they expect the 19x8.5 with an offset of approx 40 to weigh about 20.45lbs so just over 9.2kg per wheel... seems more like it for forged! 🤞
-
So currently sorting prices for a set of these..... Forged wheels weighing about 10kg for 19x8.5, custom pcd,offset, colour etc! if anyone is interested they are coming in at about £1k a set delivered 😎
-
Yea I know what you mean! Although I do like the 7.5 side vents over the 7
-
These are my 18” concave wheels when I had my mk6r. Set 2 looks very similar to this although I think the photo is of a 15x8 so the concave looks very big
-
Factory direct so not any specific brand. Saving me a few pennies going direct even if I want just 1 set..... if anyone is interested in these drop me a message as more sets would = more discount!
-
I’ve a very similar set in 18” that fit no problem so should be fine! 😎
-
Been thinking of new wheels etc and thought I’d put my professional experience to use and source some alloy wheels directly from the factories I’ve dealt with over the past 20 or so years.... I think I’m down to 2 sets so what do you guys think?? Set 1 or 2 ??? 🤷♂️🤷♂️🤷♂️
-
Still haven’t fitted any of the parts I’ve got but did have time today to give her a nice clean.... I always feel like you get to know a car better once you e cleaned it a few times!
-
To keep or not to keep? (Pretoria wheels)
ben120280 replied to ben120280's topic in VW Golf R MK7 Chat
Send me a message if you are interested Mike 👍 -
To keep or not to keep? (Pretoria wheels)
ben120280 replied to ben120280's topic in VW Golf R MK7 Chat
Very nice wheels... -
To keep or not to keep? (Pretoria wheels)
ben120280 replied to ben120280's topic in VW Golf R MK7 Chat
Thanks for the input peeps.... If I could afford the aftermarket wheels without selling the Prets I would, but alas I just don't have £1k spare (well i do but with a family, there are more boring and important things to spend it on!) Tis a proper dilema but i already feel the pull of new wheels so will probably look at selling them... -
Having worked in the alloy wheel industry for many years, I’ve always swapped and changed my wheels regularly (as in every 6 months for probably the past 10+years!!) Mostly this was because I got them at cost price, so I was able to run a set of wheels and tyres for 6 months and sell them for less than what I paid for them, or there abouts. Thing is, I no longer have that option due to a new job, but I still get the itch! Currently I have original 19" Prets and whilst they are nice, they wouldn’t necessarily be my first option. So, I’m thinking of selling them to fund a new set but wonder if I my regret that in 4 years’ time when I look at selling the car? So what do you lot recon? Stick with the prets or sell and get something else? (I like the BOLA CS-R 😎)
-
🤦🏻♂️ AliExpress! 🤣