Rob928
Members-
Posts
32 -
Joined
-
Last visited
Rob928's Achievements
Advanced Member (3/9)
1
Reputation
-
SevenR reacted to a post in a topic:
Has anyone put the standard golf r 7 on rolling road yet ?
-
The gearbox has been replaced and on the test drive they found a broken shock, front left but why only replace three and why would the rear need doing if the front where an issue??? I will probably head down Monday to check the car out myself I'm still waiting for hq to call me, I was also billed for fuel in my first hire car that I didn't even drive after a long argument I got my money back been a bit of a nightmare so far with the car :/
-
To add insult to injury, the gearbox was all finished road tested and ready for collection, then I had a call to say I need a new front shock absorber, they then told me they are replacing 3 of them and I will have to wait for a few more weeks for the parts to be shipped. As you can tell I'm not overly satisfied or impressed with the car anymore 5k on the clock and this many issues isn't right for any car let a lone a brand new VW. Waiting to hear from HQ now as I've filed a complaint about the vehicle. They told me they will look into a 'good will' gesture but what should I expect no car for two months with two issues within such a short period what would you do if it was your car?
-
Same thing with the mechatronics unit faulty but vw requested a total gearbox replacement they've had the car two weeks and it's hopefully ready soon, hats off to my garage though, they didn't know the car was coming until an hour before as the vw assist guy was sending it to audi they told me we can't do it til the Wednesday, had a call Monday afternoon saying we've diagnosed it gearbox is on order and we are pushing for a faster shipment for the box. I honestly haven't had a better dealer through and through from the sale to service.
-
So unfortunat,ey today after a weekend away with some friends my gearbox had a failure started to come up with no reverse gear and then had only 2nd gear then to no gears, had the guys come and have a look couldn't fix it so they organised a two truck to take me the 100 mile trip home and then collecting the car tomorrow to be fixed and delivering a courtesy car. Yes it's a massive pain it's happened but fantastic service within an hour and a half of the first call I was on the truck and going home. Has anyone else had any issues like this I was told that the car isn't selection one side of the gearbox eg 3rd ect
-
In settings you can set a timer so the screen turns off nearly fully it is slightly backlit to say its on but that's what I use at night the screen comes on when you move your hand to it and goes off after the time you set. Hope this helps
-
Same thing it's a shame with the 18s they sit to far in for the arches there is a thread on here about it
-
I've put some pictures up off mine on here so should be about
-
Currently waiting for roadside assistance......
Rob928 replied to AC14RKE's topic in VW Golf R MK7 Chat
Used to happen all the time on my astra vxr and it would always be the ones I couldn't get to typically hope you get it sorted mate -
How much are they do you know roughly?? I'm not bothered overly on price as I think it will transform the look I've got the Cadiz alloys as personally didn't want the preys as I found them simiar to my astra vxr wheels
-
I'm so glad it's not just me with this!! I'm really wanting to do spacers I love the wider arches but they need filling anyone done this I would love to see the results and get a link to where and oh much for the spacers as I will snap them up quickly!!
-
Advice needed on MK7 GOLF R CONVERSION Pleaaaseee :)
Rob928 replied to Golfrconversion's topic in VW Golf R MK7 Chat
Honestly and truthfully I wouldn't want to waste my money nor time on doing a project like this but fair play for doing it, the thing is yes it may be the first replica but if it's done correctly and it's at a car show for example who's to know it is a replica?? Why not, as stated be different and modify the car you've got with what you've got OEM+ for me would be perfect. You will receive negatives as well doing a rep as everyone here owns the car, and being told you could easily have one could be offensive to some as people have worked hard to get hold of these cars even though it says I'm not bragging, it comes across as otherwise. I will also say at the end of the OP it states what do you guys think everyone has just given the option that has been asked for. Best of luck with the conversion anyway. -
Just got back from the nurburgring and saw this testing honestly does look spot on in the flesh pictures don't do it justice
-
Has anyone put the standard golf r 7 on rolling road yet ?
Rob928 replied to Dwytho's topic in Modifying your Golf R MK7
Haha no worries -
Has anyone put the standard golf r 7 on rolling road yet ?
Rob928 replied to Dwytho's topic in Modifying your Golf R MK7
My mate just wrote me this for transmission loss: Think of this, you have a car that produces 250bhp at the wheels making approximately 295bhp at the fly. This is a loss of 45bhp. You then tune this car to 450bhp at the wheels. By the 15% rule that would have gained from 285bhp to over 515bhp at the fly. So the losses have some how gone from 45bhp to 65bhp? No they haven't the same transmission means the same amount of loss to frictions in the transmission and tyres. In reality the car is only tuned from 295bhp to 495bhp. Let's analyse the components of a power figure a bit more starting with an engine dyno. First of all most dynos apart from inertia only use some sort of brake to control the load applied to the car. This load is then absorbed by the break and this power is then measured at the brake with a load cell and tacho metre to get the torque at the brake with the RPM of the shaft giving power. The engine dyno simply works this way, power is measured in a steady state so the brake is applying an equal force to the engine as the engine is making hence the term brake horse power. As when forces are equal what is in motion stays in motion and no acceleration or deceleration takes place. However this is quite a long process to step the engine up through its rev range, stablise and take a measurement. People tend to use a sweep test or a ramp test where a controlled rate of acceleration is allowed. If you now looked at the readings at the brake you'll find infact the measurements have dropped. This means that some of the power that was there at a steady state has been lost. You need to look at the inertia of the dyno now, there are rotating components which have mass and resist being accelerated or decelerated this is known as their moment of inertia. The faster your allow acceleration the less brake power you see. Force = Mass x Acceleration Torque = Inertia x Angular Acceleration You now need to know the exact inertial mass for the dyno components in order to correct back to the original braked figure. Now on an engine dyno this is easy as you know the mass of the components of the dyno and no matter what engine you chuck on it you'll get this staying consistent. The only final part is to add a tiny bit more power for any power lost to bearings friction which is known as parasitics. Now lets look into chassis dynos, proper braked or loaded dynos work in the same way, except you now have a larger amount of inertia and parasitics to deal with. The rollers have a larger amount of inertia which needs to be known exactly. This is fairly easy as when you build the dyno you can measure it. So lets strap your car down and do a power run, you get a figure awesome. But lets change the acceleration rate to be faster, suddenly you get less power? Ok lets do a steady state measurement and you get more power? Well whats going on? It's more inertia involved, your wheels, drive shafts, gearsets, etc etc all have mass. But how much inertia is there? No one really knows, you could ask the manufacturer but what if you put after market wheels on or a lightened fly wheel? This means you've changed the inertia amount. The truth is unless you dyno operator spends half an hour doing pulls at different speeds at different acceleration rates and steady state measuring the power at fixed RPM points to ensure the power figures stay the same it probably means he's not even measuring inertia and therefore even your wheel power figure correctly. Fly wheel power then is your wheel steady state + parasitics of your transmission. There are two ways this is done typically. Dyno Dynamics use a fixed known average between different types of engines and chassis to give a guess. The second method is to use a coast down, but this relies on the inertia of the dyno and drive train to be correctly programmed as the deceleration rate is used with a known mass to work out the power loss. Again as I said literally no one measures the inertia of the drive train properly therefore pretty much all figures are inaccurate. Dyno Dynamics use a shootout mode which locks the drive train inertia, the acceleration rate and the transmission parastics to a fixed setting so it cant be tampered with. So provided the operator does his job right you can go on many different dyno dynamics and get the same figures. Not accurate figures but repeatable. Dyno Dynamics will be cheated if you change the inertia of the vehicle from one run to another or even change your brand of gear oil as the reality of the losses will change but the compensations are static. Coast down dynos really relies on the operator putting the right inertia in and on a dyno day they've never going to waste time doing this. Not to mention companies that deliberately put too much inertia just to make them selves look good. So basically you can throw your graphs in the bin if you're trying to get an engine fly wheel figure that is accurate. The correct way to use a Dyno is to do before and after, as long as you have more fairy dust then when you started you have a positive improvement. Repeatability to measure differences between changes is the key not to be accurate here. -
Own a tornado red decided on that to be different basically and it's a lovley colour yes blue is stunning as well but reds a bit different