Jump to content

WeeG

Members
  • Posts

    32
  • Joined

  • Last visited

About WeeG

  • Birthday 26/10/1988

Profile Information

  • Location
    West Coast of Scotland
  • Interests
    Rugby, CARS, gym, shooting, fishing, women in no particular order :P

WeeG's Achievements

Advanced Member

Advanced Member (3/9)

0

Reputation

  1. The APR car was stock apart from a first revision APR stage 1 file. The car is also hardly run in. I think with no interioer and one passenger a high 11 would be achievable with stock mods and map. 375 bhp and 414 lbs/ft is pretty good from just a map on a golf R
  2. Hey invisiblekid The car requires to run the 104 octane file but can run on 99 octane fuel puls 50/50 water meth. The inlet manifold allows equal distribution of air to each cylinder compared to standard the runners are a lot bigger and the system is a lot more efficient than OEM, it actually aids timing with less correction factor so that and the WMI allow the car to run safely on the 104 ocatne file Stage 3 could be on the cards the trouble is traction. Above 3rd gear on the R888's the car is quite gripy in the dry. in 3rd on boost there is a little traction control flashing and then it takes off It goes really well tbh. Pulled away quite easily against a close friends 420 bhp focus RS Revo stage 4.
  3. Hey folks a few updtes over the last few months. I had the Devils Own water methanol injection set up put on the car and also my custom inlet manifold was created and supplied by one of Ecotune's foreign counterparts With the inlet manifold 50/50 WMI mix and APR v3.4 race file some good numbers were had here is a few photos
  4. Well apart from the new Leon Cupra mk3 on dry track
  5. The fact its on the dyno as well never helps with the "real" noise. I think surprisingly enough on the Golf R clip it sounds good and it looks really good too
  6. Als standard 7R with 99 V power full interior and 3/4 tank of fuel did a 12.9 at 105 mph....
  7. You should checkyour DV. 300 g/s is very high compared to most remaps on stage 2+ i have ever seen unless running the new APR code with the re calibrated boost control. Then you should see 300+ otherwise with revo i used to see 260ish with the new revo ceramic intake and 250ish with ITG
  8. The torque will be way out on awesome GTI's rollers they claim it's a ft/lbs read out but i would have to argue it must be nm, as the torque figures are totally unrealistic.
  9. QUite surprising imo, still think the new leon doesn't look much
  10. Gave the car a good wash, polish and wax today using poor boys products
  11. Not sure about stage 1, but stage 2+ peaks at 1.8 and drop to about 1.4 at the red line I'm running the V3.31 2+ APR file... It is actually the v3.4 file as v3.31 was for the US and v3.4 is for ROW. But at the time of early release I wanted mine so quick, that my version is the 3.31 one. My car shows max of 2450 mbar in VCDS around 4000rpm. 2100mbar at redline. My Polar FIS+ Advanced shows max just under 1.6 bar around 4000rpm if that helps. 2450 mbar is low.... You aren't running a DV+ are you?
  12. Here is the deal, the boost achieved cannot be replicated on the standard ECU boost values. APR recreated the rerquested boost that could be achieved. On vagcom you cannot register the amount of boost so what your saying is nobody knows what boost there running? or am i reading it wrong? My car sees 2800 mbar
×
×
  • Create New...