Jump to content

Headlight range control module


Olifran

Recommended Posts

Olifran: Thanks for the screen shots.

 

hmm.... OK. You are using the latest Ross-Tech software and a HEX+CAN  cable. Software is good, but you need to remember that the design of the HEX+CAN device is now over 20 years old. Ross Tech have faithfully supported these older cables through the intervening years, but CAN standards on newer release cars have now progressed beyond the capabilities of the HEX+CAN cables.

 

For example, one of the protocols that the HEX+CAN cable can't read is newest Extended Address Mode that is enshrined in the latest CAN 2.0 B standard  (this protocol uses 29 x Bit addressing). Your first screen suggests that this inability to communicate with "Extended address" is causing the fault message to be truncated. Your last screen suggests that this same problem is causing the auto-scan to be not fully completed because at least one of the modules in your car has OBD 2.0 B protocol (I suspect one of the LCM modules).

 

Bottom line- if you want to keep abreast of the modules in the newer VAG  vehicles that use  current OBD  standards, then you will need to upgrade your  VCDS cable (HEX-NET, or HEX V2). Ross Tech has a kind-of "loyalty" offer for those that are in your situation - you can "trade-in" your old cable for a newer HEX series product at a discounted price ( see https://store.ross-tech.com/shop/RetCAN )

 

Don

 

PS: although it may seem that I am "sprooking" sales for VCDS - I have absolutely no affiliation with Ross-Tech. I simply happen to believe (as a user) that they have an excellent range of diagnostic cables!!

Link to comment
Share on other sites

27 minutes ago, dv52 said:

Olifran: Thanks for the screen shots.

 

hmm.... OK. You are using the latest Ross-Tech software and a HEX+CAN  cable. Software is good, but you need to remember that the design of the HEX+CAN device is now over 20 years old. Ross Tech have faithfully supported these older cables through the intervening years, but CAN standards on newer release cars have now progressed beyond the capabilities of the HEX+CAN cables.

 

For example, one of the protocols that the HEX+CAN cable can't read is newest Extended Address Mode that is enshrined in the latest CAN 2.0 B standard  (this protocol uses 29 x Bit addressing). Your first screen suggests that this inability to communicate with "Extended address" is causing the fault message to be truncated. Your last screen suggests that this same problem is causing the auto-scan to be not fully completed because at least one of the modules in your car has OBD 2.0 B protocol (I suspect one of the LCM modules).

 

Bottom line- if you want to keep abreast of the modules in the newer VAG  vehicles that use  current OBD  standards, then you will need to upgrade your  VCDS cable (HEX-NET, or HEX V2). Ross Tech has a kind-of "loyalty" offer for those that are in your situation - you can "trade-in" your old cable for a newer HEX series product at a discounted price ( see https://store.ross-tech.com/shop/RetCAN )

 

Don

 

PS: although it may seem that I am "sprooking" sales for VCDS - I have absolutely no affiliation with Ross-Tech. I simply happen to believe (as a user) that they have an excellent range of diagnostic cables!!

Thank you for the info. Will the new lead be able to read the headlight modules for the mk7.5?

Link to comment
Share on other sites

^^^ the headlight modules for the mk7.5 are LCM (light Control Modules) that I referenced in my reply - Answer = Yes . Have a look at the modules @ 29, 39, D6 and D7 in the auto-scan on the link below (not a mk7, but the new Tiggy uses very similar modules)

 

http://162.208.84.227/showthread.php?13213-2018-Tiguan-AD1-2-0-BiTDI-CUAA

 

Don

 

PS:The newer HEX series cables certainly can read LCMs,  but don't expect that you will be able to change any parameters in these modules - they have no code-sting and virtually no adaptation channels. Basically, hard wired units -alas!

 

 

Link to comment
Share on other sites

Well I found out that I needed to go into can gateway on 19 and tick all the installations in my

car from my original scan when I bought it. I think when I used OBDELEVEN, I must have enabled and disabled some gateways. 

 

You live and learn!

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
  • Current Donation Goals

    • Raised £170
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...