Jump to content

Traction light


Jmoore88

Recommended Posts

It may hopefully just need priming which can be done with an obd11 device or similar.

Happened to me a while back, thought the worst but primed it and engaged clutches and all worked again. Maybe it shuts down if not enough oil getting in, but doesn't throw an error or anything. Best to try before thinking about new pump and big £££.

Do you actually get any wheelspin from the front, if launching you should get loads if the Haldex is not working.

Link to comment
Share on other sites

34 minutes ago, SpursMadDave said:

It may hopefully just need priming which can be done with an obd11 device or similar.

Happened to me a while back, thought the worst but primed it and engaged clutches and all worked again. Maybe it shuts down if not enough oil getting in, but doesn't throw an error or anything. Best to try before thinking about new pump and big £££.

Do you actually get any wheelspin from the front, if launching you should get loads if the Haldex is not working.

 It's covered under warranty but to save me driving miles back to the garage I said I'd repair it my self if he funded the money but having another read it says it needs recoded to the car so it's going to be a garage job anyway. It's only drivable with traction control off but spins straight away

Link to comment
Share on other sites

17 minutes ago, Jmoore88 said:

 It's covered under warranty but to save me driving miles back to the garage I said I'd repair it my self if he funded the money but having another read it says it needs recoded to the car so it's going to be a garage job anyway. It's only drivable with traction control off but spins straight away


A new haldex pump doesn’t need coded to the car. It just needs primed/re-learned via a scan tool such as VCDS or OBD11.
 

As Dave says, worth replacing oil, cleaning filter and priming/re-learning first as that can sort a lot of issues. New haldex pump is circa £200, so not the end of the world if it has failed. If you have warranty send it straight back to garage. Is it a VW dealer you got it from?

Link to comment
Share on other sites

14 minutes ago, Deano said:


A new haldex pump doesn’t need coded to the car. It just needs primed/re-learned via a scan tool such as VCDS or OBD11.
 

As Dave says, worth replacing oil, cleaning filter and priming/re-learning first as that can sort a lot of issues. New haldex pump is circa £200, so not the end of the world if it has failed. If you have warranty send it straight back to garage. Is it a VW dealer you got it from?

Not a vw garage but a reputable one, the guys says hel pay any costs to have it repaired. I'd posted this before he rang and said he'd cover the costs, iv had the pump out and it was black inside so chances are it's ran dry and seized anyway so new pumps on the cards

Link to comment
Share on other sites

It might also be worth checking that the gear in the transfer case (bevel box) isn't slipping on its shaft, this will turn your AWD R into a FWD wheel spinner.   Most common on cars that have done lots of launches, especially tuned ones.

 

There are a few YT videos around describing how to check (it isn't that easy to diagnose, and some people get it wrong)

Link to comment
Share on other sites

7 hours ago, gregozedobe said:

It might also be worth checking that the gear in the transfer case (bevel box) isn't slipping on its shaft, this will turn your AWD R into a FWD wheel spinner.   Most common on cars that have done lots of launches, especially tuned ones.

 

There are a few YT videos around describing how to check (it isn't that easy to diagnose, and some people get it wrong)

Will have a look now thanks

Link to comment
Share on other sites

11 hours ago, gregozedobe said:

It might also be worth checking that the gear in the transfer case (bevel box) isn't slipping on its shaft, this will turn your AWD R into a FWD wheel spinner.   Most common on cars that have done lots of launches, especially tuned ones.

 

There are a few YT videos around describing how to check (it isn't that easy to diagnose, and some people get it wrong)

Had a look at the videos theys no loud noises or banging from my car so hopefully not the bevel box shaft

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
  • Current Donation Goals

    • Raised £170
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...