Zaphire

Unfortunately not no. I got mine when they first came out, on PCP. I wanted one so bad i took one that was siting on the forecourt that someone else had ordered and then cancelled. Needless to say, it's bit me on the arse a bit as the settlement figure is ~22K with a GFV of 13K iirc.

14 plate, Prets, Sunroof, DSG, Lapiz, 26k on the clock.... £17K max

I've done that mod on mine and I can confirm that the lights stay on when leaving the car without messing around with the indicator stalk. I never even knew you had to mess around with it before doing it :I

Yeah I got them all from there/first page of the thread!

Out of curiosity, what's the difference between one of these pedal boxes and say a DSG remap? I was planning on getting a stage 1 APR ECU map and the gearbox done at the same time. However, if it's cheaper, and the results are the same, I'll just go for one of these instead.

They shouldn't really need changing yet unless you want to. At 26K mines are just about ready to be changed, although I reckon I could probably get to at least 30K as there's 4mm left on them. Anyway, I'm interested in new discs and pads too.

No problem, happy I could help. Yeah it's a bit of trial and error really! The link I posted in my previous post helped loads. I'm sure there's even more out there somewhere!

You can However you need to do these both in the following order. DRLs stay on with turn signal 09 - Central Electronics Adaptation - 10 (8)-Leuchte2SL VLB10-Lichtfunktion C 2 -> "not active" (default "Blinken links aktiv (beide Phasen)") (8)-Leuchte4TFL LB4-Lichtfunktion C 4 -> "not active" (default "Blinken links aktiv (beide Phasen)") (8)-Leuchte3SL VRB21-Lichtfunktion C 3 -> "not active" (default "Blinken rechts aktiv (beide Phasen)") (8)-Leuchte5 TFL RB32-Lichtfunktion C 5 -> "not active" (default "Blinken rechts aktiv (beide Phasen)") Dimming DRLs with turn signal First do the coding above for DRLs to stay on with turn signal 09 - Central Electronics Adaptation - 10 (16)-Leuchte2SL VLB10-Lichfunktion G 2 -> "Blinken links aktiv (beide Phasen)" (default "not active") (18)-Leuchte2SL VLB10-Dimmwert GH 2 -> "25" (default "0") (19)-Leuchte2SL VLB10-Dimming Direction GH 2 -> "minimize" (default "maximize") (16)-Leuchte3SL VRB21-Lichfunktion G 3 -> "Blinken rechts aktiv (beide Phasen)" (default "not active") (18)-Leuchte3SL VRB21-Dimmwert GH 3 -> "25" (default "0") (19)-Leuchte2SL VRB21-Dimming Direction GH 3 -> "minimize" (default "maximize") You can even get the DRL's to blink when you indicate if you wanted! I'll repost this doc that someone else shared, loads of useful stuff in it. https://docs.google.com/document/d/151DX1D0BEs76UfUpJbBAVJ8OhuhEoRPrmxFsUrKiVm0/pub

Is comfort blinking not this: Change comfort blinking 09 - Central Electronics Adaptation - 10 (2) - Turn Signal Control-Komfortblinken Blinkzykien Default is 3, add can be set as high as 5 flashes In head unit, reset Car - Setup - Factory Settings - Lights

Honestly, I hope nobody buys the facelift until the second revision of the infotainment system is out. Don't make the mistake I did and get stung by the 1st gen system. (MIB 1)

I'll give it a comparison tomorrow as it's a little late now, just back in. Coded the exhaust flaps mod, and I didn't really notice a difference when feeling the air coming from the exhaust. The two inner exhausts have a much larger flow of air compared to the two outer ones, which is near non-existent. Followed the guide on here and bit 2 is unticked (Hex 00) when ticked it was Hex 04

Either really. Was just wondering if the extra numbers over 100 actually made any difference.

Awesome piece of kit. Managed some mods already. Out of curiosity, some of the changes, for lights for example allow you to go up to 126 or 127. Should you stick to 100 or put them the full way?

I highly doubt it. Fair enough mines is a 14 plate, but it does have options, DSG and I'm only being offered around 18K. The price of these cars are tanking and there's nothing we can do about it as the market was flooded.

Coming from someone with a 14 plate MIB 1 HMI system, I'd stay away from these.