AdDaMan Posted October 28, 2015 Report Share Posted October 28, 2015 Do you need vsds to clear the code you get from pulling the plug? Quote Link to comment Share on other sites More sharing options...
Stobsie Posted October 28, 2015 Report Share Posted October 28, 2015 Do you need vsds to clear the code you get from pulling the plug? Oh I see where this is going.. Lol Quote Link to comment Share on other sites More sharing options...
AdDaMan Posted October 28, 2015 Report Share Posted October 28, 2015 Oh I see where this is going.. LolHaha! Only if and when lol Quote Link to comment Share on other sites More sharing options...
Stobsie Posted October 28, 2015 Report Share Posted October 28, 2015 Haha! Only if and when lol It's always here if & when needed. AdDaMan 1 Quote Link to comment Share on other sites More sharing options...
andy3141 Posted October 28, 2015 Report Share Posted October 28, 2015 Mine was pulled a week ago, I will do a VCDS scan tomorrow and see what turns up Quote Link to comment Share on other sites More sharing options...
TecklenburgVW Posted November 16, 2015 Report Share Posted November 16, 2015 There is an easier way to disable the rear Haldex electronically and engage dyno mode... Drive the car onto the Rollers. Switch off. Turn Ignition on When the dash lights go off like abs etc Switch on the hazards pump the throttle 5times You will notice the traction control light will come on. You are now in dyno mode. Leave hazards on Start and the rear wheels will be deactivated. When you switch off dyno mode will be deactivated. Dyno mode is also deactivated if the rear wheels turn like on the Road Not sure if the sequence will be exactly the same bud, but there certainly is a dyno mode on the 7. I'll give it a blast and report back. - Did the above method work on your Mk. 7 Golf R? Quote Link to comment Share on other sites More sharing options...
Stocky Posted November 20, 2015 Report Share Posted November 20, 2015 Yes it is located under the rear passanger side seat. Heading to the dyno tomorrow, Pulled the seat up and see the connector. Def passenger side and only 1 connecter once you lift the black oval cover? Just looking for confirmation so there is no incidents on the dyno haha Quote Link to comment Share on other sites More sharing options...
Shorty Posted November 20, 2015 Report Share Posted November 20, 2015 Heading to the dyno tomorrow, Pulled the seat up and see the connector. Def passenger side and only 1 connecter once you lift the black oval cover? Just looking for confirmation so there is no incidents on the dyno haha That's the one. Stocky 1 Quote Link to comment Share on other sites More sharing options...
tautvydasv Posted December 7, 2015 Report Share Posted December 7, 2015 Passenger is on the left? Quote Link to comment Share on other sites More sharing options...
keano Posted January 29, 2016 Report Share Posted January 29, 2016 So I am wanting to get my car onto a dyno - the operator of choice uses a mustangs dyno. What do I need to know to get this done safely? ie without the haldex kicking in? It appears pulling a plug of some sort will disable the haldex? Are there any consequences to this in terms of when VW take a look at the car? Or will they just see a fault and since all is working again, clear it and carry on? Anyone got any pics of whats to be pulled? Ta. Quote Link to comment Share on other sites More sharing options...
chris_blue Posted January 29, 2016 Report Share Posted January 29, 2016 Anyone know best prices for a Dynomometer run? Ive usually paid around £80 for 2 runs, 2 printpouts, one as a joint print out, and then advice as to increase power, which usually involves advice round bigger exhaust and sports catalyric converter, then tuning of some sort (Remap) Would love to find somewhere 2 runs for £50 Quote Link to comment Share on other sites More sharing options...
GrayMK7R Posted January 29, 2016 Report Share Posted January 29, 2016 I dyno'd mine on a 4WD dyno and just turned of the traction control, the car ran fine. If you are doing it on a 2WD dyno, i'd use the trick with the hazards (but test the traction on the road first!!). pulling the haldex fuse can make the diff get very hot. Quote Link to comment Share on other sites More sharing options...
PocketRocket Posted February 20, 2017 Report Share Posted February 20, 2017 Bumping this up. Is the trick with Hazard button activated an 5 pumps on the throttle Confirmed onto the 7R? In some cases the the price for 2wd and 4wd dyno pulls is different. Would be great to know. Thanks Quote Link to comment Share on other sites More sharing options...
GrayMK7R Posted February 20, 2017 Report Share Posted February 20, 2017 Bumping this up. Is the trick with Hazard button activated an 5 pumps on the throttle Confirmed onto the 7R? In some cases the the price for 2wd and 4wd dyno pulls is different. Would be great to know. Thanks Yes, ive tried it. As others have said in this thread, better to pull the Haldex fuse for certainty Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.