Jump to content

DazR

Junior Members
  • Posts

    27
  • Joined

  • Last visited

Everything posted by DazR

  1. Great mods you’ve done, could I ask what you used for the front and rear badges? Does the front badge mod affect the radar Thanks Daz
  2. I would deffo buy the D-Plug extension Regards Daz
  3. I’ve heard a lot of people disconnecting or dialling out the start stop feature
  4. I find mine in Race pops on overrun, my previous R was loud with pop and bang map, I don’t miss it to be totally honest
  5. Just wondered why you didn’t like the JB4 as most people think it is very very good..
  6. Nobody else making these D plug extensions?
  7. Thanks, I will try your suggestions
  8. How come I need traction off...? What revs do you suggest starting from, the log needed does it need gradual throttle up to the rev limiter or full attack on the pedal avoiding the kick down switch.. Thanks Daz
  9. Who can advise on best way to get a 3rd gear log, I’m currently using map 4 (7 speed dsg) I go manual mode M3 put throttle right down at 2500 revs and it down shifts to M2, must be doing something wrong Thanks Daz
  10. Rob Just wondered if you have any AFR loom and D-Plug extensions for the 2019 WLTP Golf R currently. Thanks Daz
  11. I’m still amazed that even the garage owners on here have had little if not zero input into what bolts should be changed regardless of VW service manual, also not a single comment about how to do the job from beginning to end, I’m sure people that want to have a tackle themselves would appreciate free advice!
  12. Stephen I’ve just read your comments again, I hope you could clarify something for me, you said that it is not necessary to lower the front subframe although it’s tricky getting the transfer box off. Are you saying that you separated the transfer box from the gearbox which I think would mean removing the driveshafts then axle splines shaft,by removing the Allen bolt deep in the axle spline shaft. Ive not heard this way before so I was interested if this is the case or you managed to get the complete gearbox and transfer box by the front subframe. All the best Daz
  13. Thanks for letting me know your knowledge of TTY bolts, as I have already said I would replace the required bolts if doing this job. So who has done the job of removing and replacing the gearbox, what bolts did you replace out of interest. All the best Daz
  14. Thanks for the replies, so then no need to lower the front subframe slightly to have more clearance, great stuff. Replacing bolts I would agree is the way forward but people that have reused bolts would be quite high to be honest, I asked quite a lot of other people and they have had no issues. I suppose it is down to each persons opinion. Any other tips or tricks would be uselful. Thanks Daz
  15. Hi Guys I have got into a debate with a few buddies about the easiest way of getting the manual gearbox out of the Golf R, so I thought I would ask you experts also. I have a few that suggest that the subframe is lowered slightly and this allows enough clearance to get the gearbox out without having to take the axle drive flanges out of the gearbox. Others have suggested if the front subframe is lowered then a full geometry alignment is needed so they remove the axle drive flanges. How many of you guys fit new bolts on refitting the gearbox as they’re stretch bolts, a few have suggested slightly less torque and using loctite solves the need to fit new bolts as you have not torqued up to the original stretch limit. I look forward to your comments Thanks Daz
  16. I was talking to a buddy who has clutch problems on his 7R, he doesn’t seem to get great gear changes,he mentioned the Sachs sintered plate with gearside stamped on it should be facing the flywheel with dual mass flywheel set up, I said surely it means gearbox side. Im confused about that 😭
  17. Could you advise on which release bearing to use with the Sach Clutch, is it a specific Sach part? Thank you Daz
  18. Hi Guys I have been reading through lots of info with regards to upgrading the clutch on the manual R, could any of you recommend the best throw out bearing to compliment this set up, as I have also read it is a specific part to the Sachs SRE kit with the sintered plate. could anybody advise. Regards Daz
  19. Could you possibly explain what effects it would have by changing timing values on the different modes, engine knock?
  20. Thank you thank you so much for helping with this.. Regards Daz
  21. Hi Oh great thanks for this info, I’m still trying to work out how the sps is set up through the obd, don’t seem to be much info on google!
×
×
  • Create New...