Rainer1
New Members-
Posts
17 -
Joined
-
Last visited
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
Rainer1's Achievements
Member (2/9)
1
Reputation
-
Rainer1 reacted to a post in a topic:
MK7.5 timing chain or belt?
-
It does not make sense recalibrating lowering springs. The run out that houses the spring will be the same hight as before when tightening them in to seat them inside. There is no play, as they will touch inside bottom to top. So, when you jack all 4 wheels up your wheels end up in the same position as before hence hardly any difference in calibration number changes All lowering springs do, is reduce compression force by being a little shorter but no shorter than the actual oem fitting that houses the springs. Spring resistence by design will also be less hence the ... drop when you sit the car down on to the ground. All that is needed is wheel alighnment. Anyone stating that recalibrating a DCC did wonders is imagening.
-
It does not make sense recalibrating lowering springs. The run out that houses the spring will be the same hight as before when tightening them in to seat them inside. There is no play, as they will touch inside bottom to top. So, when you jack all 4 wheels up your wheels end up in the same position as before hence hardly any difference in calibration number changes All lowering springs do, is reduce compression force by being a little shorter but no shorter than the actual oem fitting that houses the springs. Spring resistence by design will also be less hence the ... drop when you sit the car down on to the ground. All that is needed is wheel alighnment. Anyone stating that recalibrating a DCC did wonders is imagening.
-
I run 462 nm at the wheels. The Higher torque is usualy @ the crank. So, you should be fine. I run 400 hp @ crank and of course higher nm. My DSG is tuned to accomodate this torque. I give it a good flogging every now and then and no issues @ 2.5 yars later. Clutch plates pressure is increased with a DSG tune. I recommend this to anyone who has the ECU tuned. It is night and day from the oem DSG tune.
-
DQ381 DSG – Delayed Gear Engagement / Free Revving Issue
Rainer1 replied to Daveyjones457's topic in VW Golf R MK7 Chat
Seems vast differences on service schedules. I have the year 2020 mk 7.5. In Australia VW recommended DSG service @ 120,000 km. I think this being too long and I get it serviced every @ 70,000 km. Especialy since i run 400hp with DSG tuned also. -
Rainer1 reacted to a post in a topic:
DQ381 DSG – Delayed Gear Engagement / Free Revving Issue
-
I aggree! I researched pretty much all progressive springs and concluded Leyo being the best choice for my Golf R on now 18 inch wheels. They are ACC compatible. I contacted Leyo regarding recalibration. No recalibration needed. It makes sense as the springs fill the housing up just the same. So, even when you have wherls off the ground to do a recalibration, the lenght is exactly the same. No change. The only thing changed is less compression on the new lowering springs. The ride is what i expected and still comfortale. I am happy with them and recommend these to anyone.👍🇦🇺
-
Rainer1 reacted to a post in a topic:
Lowering Springs
-
Yes. Leyo i opted for. 👍🇦🇺
-
Rainer1 reacted to a post in a topic:
Lowering Springs
-
I would deter from lowering a car runnong 19 inch wheels as they are already a challenge on harsh bumps and pot holes. I have 18 inch so it's fine on them. I lowered my car with Leyo Springs compatible with DCC. The drop is 2.5 cm. It is a firmer ride but still retaining some comfort. I tried a recalibration but i did not meet the rewuired conditions so OBD11 could not recalibrate. This is because my front assist sensor is malfunctioning. May need yo check the plug e.t.c as i had it apart for fitting an intercooler. If it turns out to be a sensor replacement, then i won't bother as they are too costly. I also doubt that it will make any significant improvement on these springs.
-
-
Is an Intercooler necessary for stage 2?
Rainer1 replied to Toog's topic in Modifying your Golf R MK7
Depends. Winter here in Ozz is not like winter on Europe. I certainly noticed the difference performance, especialy back to back during 11c and 15c. So. Yes! A better intercooler will make a difference. How ever... If you are just an average daily driver, then i would say it not being necessary. -
Msportman reacted to a post in a topic:
Is an Intercooler necessary for stage 2?
-
Is an Intercooler necessary for stage 2?
Rainer1 replied to Toog's topic in Modifying your Golf R MK7
It is preferable if you want to make use of all the power and consistently. The OEM is not efficient enough and will start to heat soak after a couple of pulls. I run 385 hp at the crank. I ran this on an OEM and now with an up graded intercooler. The difference is night and day. -
What are all the noises the r makes after you switch it off???
Rainer1 replied to markR's topic in VW Golf R MK7 Chat
Yes. I noticed a sort of whisshing sound, kind of like something pumping air, steam engine like. Then all quite. Not heard this befor in the 3 years i had this. This happened since changing for intercooler upgrade. Hoses e.t.c are all secure, no warning lights, no power issues 🤔 -
Just make sure your Haldex is serviced regularely.