dan Posted August 14, 2017 Report Share Posted August 14, 2017 Hi guys, I'm steadly getting the parts for the Stage2 mods for my car. The next (which should have actually been the first) on my list is the address the clutch issue on my manual R. I'm looking for advice on the real options i have for running stage2 (probably MRC / Unicorn). So circa 400+bhp and circa 430lb ft torque judging my similar cars. I realise a performance clutch will be heavier that standard but want to retain comfort in the car (as i'll sit in traffic for a portion of my daily). I can see Sintered/paddle plates are available that will easily handle the torque, but depending on who i've asked have given different views on whether it will ruin some comfort what i'd like to retain. I've heard organic is better for this, but can i run this type of power? - is there an option? I'd be interested to see other peoples experences and setups with power? From what i can work out ... - Sachs orgainic - Too much power for this? - Sachs sintered-paddle - will it destroy any comfort in drive as mentioned above? - Anyone running something Helix? - Any others...? I'm not trading for a DSG.. Love the feel of manual gears too much! cheers in advance for your input people! camelsac2002 1 Quote Link to comment Share on other sites More sharing options...
rodacollier Posted August 15, 2017 Report Share Posted August 15, 2017 When I went to Unitronic stage 2 with my JB4 I started getting slipping so I went with a DMF setup from HS Tuning because I hate noises and feared what a SMF would do. It releases closer to the floor than stock and isn't as smooth as stock leaving a stop. I've continued to make mods and I feel very satisfied with the silent operation and the strong and confident engagement. My rear main seal needed replacing while they had it apart, which I've seen others mention, so I would order one just in case since it will be apart and could delay the work. http://www.hstuning.com/product_info.php?cPath=15_18&products_id=5582'16 MK7 R ManualUni 2, JB4, DP, CTS Quote Link to comment Share on other sites More sharing options...
ToRnado Posted August 15, 2017 Report Share Posted August 15, 2017 The HSTuning one has a very nice feel to it and could easily handle that sort of power. It is rated to 480 ftlbs. The only downside is the cost as you'll be importing it from America. I've actually got one sitting in my garage. I had to take it out my car as I am running around 500ftlbs now. I am currently using a Sachs sintered clutch. It does take a bit of getting used to and it is prone to the occasional judder / squeal depending on ambient temperature / humidity but it again can handle most Stage 2 and 3 set-ups. Quote Link to comment Share on other sites More sharing options...
Marty77 Posted August 15, 2017 Report Share Posted August 15, 2017 I went straight to Sachs Sintered. I don't mind the heavy pedal but I will be honest and say it's a pig in traffic, the judder and bite means it's hard to get smooth stop start crawling. Once up and running though I have had no issues with it. Also fitted Neuspeed short shifter at the same time which has the max reduced throw so the whole car feels angry and more mechanical now. If the car was a daily I would defo have gone DSG. I decided on sintered over HS Tuning due to cost and the fact that knowing me the modifying wont stop at stage 2..... Hope this helps Quote Link to comment Share on other sites More sharing options...
bodas73 Posted August 15, 2017 Report Share Posted August 15, 2017 Its a shame no one does the HS kit in the UK, anyway around the import duty (sent as a gift maybe) noticed there is an option for the clutch kit without the Dual mass flywheel option for $999.99 bit cheaper for those that dont need the flywheel http://www.hstuning.com/product_info.php?products_id=3888 Quote Link to comment Share on other sites More sharing options...
Peth Posted August 15, 2017 Report Share Posted August 15, 2017 I can vouch for the HS tuning clutch slightly heavier but no judder but as said is expensive !Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
GuyKitch Posted August 15, 2017 Report Share Posted August 15, 2017 I would recommend not spending stupid money on a HS Tuning clutch and just get a sintered sachs clutch. For the price of buying, importing and fitting a HS tuning clutch, you could have gone through two of the Sach's clutches. Also for peace of mind, I've been running a Sachs 4 puk clutch since November, Stage 3+ and no issues. It doesn't even squeal. Yes it is slightly difficult in traffic, but for a few mins of traffic who cares? Make your R a real mans car 😂✌️ also gives you the excuse to tell people that it's too tricky to drive. camelsac2002 1 Quote Link to comment Share on other sites More sharing options...
Marty77 Posted August 15, 2017 Report Share Posted August 15, 2017 34 minutes ago, GuyKitch said: I would recommend not spending stupid money on a HS Tuning clutch and just get a sintered sachs clutch. For the price of buying, importing and fitting a HS tuning clutch, you could have gone through two of the Sach's clutches. Also for peace of mind, I've been running a Sachs 4 puk clutch since November, Stage 3+ and no issues. It doesn't even squeal. Yes it is slightly difficult in traffic, but for a few mins of traffic who cares? Make your R a real mans car also gives you the excuse to tell people that it's too tricky to drive. Guy, your just showing off with your non squeeky clutch! camelsac2002 and GuyKitch 1 1 Quote Link to comment Share on other sites More sharing options...
dougaberdeen Posted August 15, 2017 Report Share Posted August 15, 2017 Pretty sure the hs tuning clutch is just made up of off the shelf Audi parts but with a couple of dowel holes drilled in the pressure plate so it all fits thread below lists the parts number so should be doable without paying a fortune and it seems to be the best in terms of OEM feel http://www.golfmk7.com/forums/showthread.php?t=18913 Quote Link to comment Share on other sites More sharing options...
rodacollier Posted August 15, 2017 Report Share Posted August 15, 2017 IMO - Unless you have your own shop for the labor and tools, the costs of the installation & re-alignment should be factored into the costs for the clutch kit. Especially any notion of 2 cheap clutches vs 1 quality solution. Also, my car has to be drivable by my wife and teenage daughter occasionally so my mechanic discouraged a few options to keep it more of a daily driver. '16 MK7 R ManualUni 2, JB4, DP, CTS Quote Link to comment Share on other sites More sharing options...
thanksabunch Posted August 15, 2017 Report Share Posted August 15, 2017 Just stick to stage 1 and go sachs organic clutch kit that's my plan Quote Link to comment Share on other sites More sharing options...
DUB Posted August 15, 2017 Report Share Posted August 15, 2017 I honestly wouldn't describe my sachs sintered as a pig to drive in traffic. I find it perfectly civilised as a daily but then again I have driven modified manual cars all my life. Occasional squeal and judder but in my opinion nothing horrendous. Quote Link to comment Share on other sites More sharing options...
DUB Posted August 15, 2017 Report Share Posted August 15, 2017 15 hours ago, ToRnado said: The HSTuning one has a very nice feel to it and could easily handle that sort of power. It is rated to 480 ftlbs. The only downside is the cost as you'll be importing it from America. I've actually got one sitting in my garage. I had to take it out my car as I am running around 500ftlbs now. I am currently using a Sachs sintered clutch. It does take a bit of getting used to and it is prone to the occasional judder / squeal depending on ambient temperature / humidity but it again can handle most Stage 2 and 3 set-ups. Are you TTE525 with a built engine? Quote Link to comment Share on other sites More sharing options...
dan Posted August 15, 2017 Author Report Share Posted August 15, 2017 cheer for the advice guys. 15 hours ago, ToRnado said: The HSTuning one has a very nice feel to it and could easily handle that sort of power. It is rated to 480 ftlbs. The only downside is the cost as you'll be importing it from America. I've actually got one sitting in my garage. I had to take it out my car as I am running around 500ftlbs now. I am currently using a Sachs sintered clutch. It does take a bit of getting used to and it is prone to the occasional judder / squeal depending on ambient temperature / humidity but it again can handle most Stage 2 and 3 set-ups. THat HST one looks good but are they overcharging? Interesting the later post with the DIY TTRS kit... would be interesting to know if those part numbers matched your HSTuning kit! Did it start to slip when you exceeded the rated 480lb ft (went 500lb ft) hence your change again? I'm told Helix do a high rated 420lbft+ organic kit... i may enquire about that in the morning and post with my findings. 29 minutes ago, Matthewsimone said: Just stick to stage 1 and go sachs organic clutch kit that's my plan That did cross my mind, but i'm sure there's something suitable. Quote Link to comment Share on other sites More sharing options...
ToRnado Posted August 16, 2017 Report Share Posted August 16, 2017 8 hours ago, DUB said: Are you TTE525 with a built engine? Yes. Quote THat HST one looks good but are they overcharging? Interesting the later post with the DIY TTRS kit... would be interesting to know if those part numbers matched your HSTuning kit! Did it start to slip when you exceeded the rated 480lb ft (went 500lb ft) hence your change again? It is pricey, yes. It is a Sachs clutch that's been modified for the R as Douglas has indicated. I'll take a look at the clutch later on and see if there are any part numbers that I can see on there. When my car was originally tuned for the TTE525, I started to get clutch slip at bang on 480ftlbs so the tune was limited to around 510hp / 477ftlbs until I fitted the Sachs sintered clutch. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.