Jump to content

Which Downpipe?


MrMK7GolfR

Recommended Posts

 
Three factors to consider are the cat dia, the cells per square inch and the cat position, all of which influence performance.
We place the cat as far away from the turbo as possible which will not allow the lambda lead to reach the rear of the cat. To overcome this we insert a miniature 200 cell cat into the secondary lambda boss to fool the ecu.
 
4.thumb.jpg.cdc40f628938f733f676b8032bb0916b.jpg
 

Thanks


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

On ‎09‎/‎03‎/‎2018 at 11:32, nige bcs said:

Catalytic Converter

 

D

Direct quote off their site ;-)

 

APR’s engineers specified a high-quality and high-flow GESI metal 300-cell catalyst ideal for forced induction application. During dyno testing, the 100mm x 100mm design showed no measurable loss in power thanks to the catalyst’s design.

catalysts catalysts

Internally the catalytic converter feature a proprietary wash coat that helps to reduce emissions and smell common on cat-less setups. The low-profile catalyst features a fully captured substrate brick, which is furnace braised to the outer mantle and physically captured by the diffuser cones preventing rattling, rotation, and damage to the substrate. Subsequently, a byproduct of running the catalyst is a reduction in noise, making the system as a whole more pleasing to the ear.

 

Isn't the quoted CELL value a figure per square inch so that overall size of the sport cat comes into play therefore a 300 Cell x 100mm length is less restrictive than a 200 Cell x 200mm length ?

 

Also, the APR quote doesn't say what they were comparing it against - a catless DP ?

 

I'm no APR fan boy just trying to understand this better. 

Link to comment
Share on other sites

1 hour ago, Rob2k68 said:

 

Isn't the quoted CELL value a figure per square inch so that overall size of the sport cat comes into play therefore a 300 Cell x 100mm length is less restrictive than a 200 Cell x 200mm length ?

 

Also, the APR quote doesn't say what they were comparing it against - a catless DP ?

 

I'm no APR fan boy just trying to understand this better. 

 

The APR cat is 100mm in dia and 100mm in length 300cpsi...

We use a monolith that is 125mm dia by 125mm in length with a choice of 100 or 200 cpsi

Cheers

Nige

Link to comment
Share on other sites

 
The APR cat is 100mm in dia and 100mm in length 300cpsi...
We use a monolith that is 125mm dia by 125mm in length with a choice of 100 or 200 cpsi
Cheers
Nige


Perfect ! - thanks Nige.

Good to have the technical data behind these.

100cpsi is the clear winner for flow but probably not a lot in it between 300cpsi and 191 cubic inch volume and 200cpsi and 374 cubic inches.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

  • 3 weeks later...
On 3/2/2018 at 06:48, Rob2k68 said:

Had the Milltek 200 cell on my stage 2 S3 which was the perfect amount of increased rasp for me - not any louder just a different tone. They've since improved it by adding a cast section to it for better air flow and I believe it's a bit cheaper.

 

If I was doing this again I'd go Scorpion as the cat is located further down closer to the joint for the res rather than immediately out of the turbo. BCS also does this and looks quality but I'm not a fan of how the wrap looks. 

 

Did you get the full Milltek system as their website specifically states that you can't mate it to the OEM system (I'm only looking for a DP at this stage)?

Link to comment
Share on other sites

6 hours ago, golf7.5r said:

 

Did you get the full Milltek system as their website specifically states that you can't mate it to the OEM system (I'm only looking for a DP at this stage)?

 

No - just the DP (older non cast version) which came in two pieces the rear section tapered down to fit the original system. This was 18 months or so ago so things may have changed . 

Link to comment
Share on other sites

20 hours ago, golf7.5r said:

 

Did you get the full Milltek system as their website specifically states that you can't mate it to the OEM system (I'm only looking for a DP at this stage)?

 

I've just checked their website and they have quite a few downpipes that mate to the OE exhaust, there's de-cat, sport cat, cast and EC-approved options (you'll pay more for the EC approval).

 

Cast with sport cat to OE pipe is this one :-

 

Large Bore Downpipe and Hi-Flow Sports Cat

For Fitment with the OE Exhaust system only and requires a Stage 2 ECU remap

 
 
 
System Number: SSXVW349
Consists of:
Tailpipe Style:
 
1 x Cast Large Bore Downpipe 200cell HJS Catalyst {Replaces MSAU616}
 
1 x Milltek Downpipe-to-OE Cat-back Connecting Pipe {4WD-only}
Link to comment
Share on other sites

  • 11 months later...
  • 2 years later...

Resurrecting an old thread here, but just wondering if rick/nige could let me know what the power limitations are for stage 3 on the bcs 100 cel (assuming fuel pumps are upgraded too). Does the limitation still sit with the strength of the block or does the downpipe kick in first? I already have the bcs downpipe on the car with Rick's stage 2 and it's brilliant! Just looking at options for stage 3 as you do get used to the power quite quickly 😀

Link to comment
Share on other sites

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
  • Current Donation Goals

    • Raised £170
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...