CAJPAJ
Junior Members-
Posts
42 -
Joined
-
Last visited
Profile Information
-
Gender
Not Telling
-
Location
UK
Personal Information
-
Name
Pete
Recent Profile Visitors
1,363 profile views
CAJPAJ's Achievements
Advanced Member (3/9)
18
Reputation
-
fastandy reacted to a post in a topic:
water pump housing
-
invisiblekid reacted to a post in a topic:
Someone's pride and joy - smashed
-
Its becoming a nightmare to own a decent car these days. Some scroat's smashed my rear house door glazed panel this morning around 03:15 with what the police said is a spring loaded centre punch but the glass was toughened so didn't fail completely. They didn't realise that I had a Ring Floodlight cam so some good pictures of one of the perps! Police attended but doubtful anyone will be caught and they escaped in black Seat Ibiza. Wife now wants rid of the car as well.
-
Changed my water pump & housing myself earlier in the year, it had only run just over 10,000 miles from new but was out of warranty. It is a fairly difficult DIY job but I managed it from underneath without removing inlet manifold although had to remove throttle body etc.. You need a small torque wrench that goes as low a 9 Nm for fitting the pump to block again and also one that can do left hand thread a the timing pulley is left hand thread bolt. I think the most fiddly job was the turbo boost pipe going over the gearbox. I purchased a new unit (INA brand) and the small plastic piece from AUTODOC for around £220. Also on refitting initially the small plastic pipe from pump to oil cooler was not seated so was leaking therefore had to remove again and was probably down to not coating with enough coolant prior to inserting into oil cooler. Was easier second time around though as I had done it before. Took the old unit apart and it appears to be a simple shaft seal had failed that goes from the motor to the valve assemblies that control water flow in and out of the pump. There is no way to change this seal without totally destroying the unit I may add! Strange why these fail randomly as my wife's S3 ( 63 plate) with more miles and the old plastic pump elements is still all ok? Newer units fitted from around 2015 have plastic glass filled nylon pump body but actual water pump body is now aluminium, noted mine was the aluminium/ plastic part but in reality they should be both aluminium. I'm expecting another failure in the future and this fault should have been acknowledged by the manufacturer years ago and been fixed properly.
-
Bnkrs1789 reacted to a post in a topic:
APR vs REVO stage 1
-
-
If you search their catalog it points to 345mm discs for the fronts but the correct part number is 600.3243.52 as shown for 340 mm. I notice a lot of catalogs point to 345 mm but this was for earlier Golf R’s before MK 7. You can get them from AUTODOC £74.38 ea fronts & £61.61 ea rear.
-
-
Have the following on mine and now found they do the same for the rear. VorderachseTechnische data of the brake discs: brake disc type Innenbelüftet, alloyed/high carbon, brake disc type outer diameter perforated, 340 mm, thickness / strength of 30 mm, minimum thickness 27 mm, height 49.8 mm, drill/hole number 10/5, weight 10.7 kg, pitch circle Ø 1 112 mm, hub bore Ø 65 mm, ABENr. KBA 60872 comparison numbers for comparison purposes: 1 K 0 615 301 AD Zimmermann article number for comparison purposes: 600.3243.52
-
Stefan88 reacted to a post in a topic:
Lumpy idle
-
Have you tried a throttle body re-adaptation (GX3) although this would normally have been done if throttle body is removed when cooling module (N493) & water pump are replaced? This is removed instead of the whole inlet manifold if you follow manufacturers instructions and needs to be clean and be correctly adapted to the engine control module or it will coke up. This can be done using VCDS and official and other tools of course. Other rough idles could be linked to leaking oil separator (PCV valve). Had a dodgy oil cap on a S3 8v on wife's car and idle was lumpy as hell. Tried throttle adaptation but could hear a slight hissing sound. Replaced cap and all was good again.
-
I was looking at a Miltek downpipe and was initially confused at the two pipes with 200 cell CAT, one is EC approved and the other is not. Price for EC was around £1,300 and non EC is closer to £700. Part number for EC approved is SSXVW350 (for connection to OEM exhaust) & SSXVW349 for non EC approved. They do look slightly different but both have the CAT in the same position as OEM so guessing would heat up quicker? APR and the likes have the CAT much further downstream and would take more to get hotter and pass the MOT no doubt? There are other part numbers as well if connecting to a full Miltek back system. https://www.milltekexhaust-roadrunnermotorsport.co.uk/291-golf-mk7-r-20-tsi-300ps Pete
-
Hi 370 bhp just with CTS elbow & GFB upgrade to diverter valve. Standard airbox other than snow grill removed. Running 99 Tesco fuel though.
-
Had the hi torque APR stage 1 & DSG tune at VRS yesterday. Stock was 303 bhp 313 lb/ft torque. Tune produced 370 bhp & 417 lb/ ft torque. The max torque is at around 3500 rpm then drops off from around 4000 rpm so definitely a torque surge is felt. All good though so far and gearbox doesn’t seek the highest gear at town speeds now which was a real annoyance to hit 5th gear at 30 mph. Some interesting cars at VRS, including the project car from VW driver mag which had new turbo and was making 480 bhp with a proper tune rather than tuning box. Another R there was tuned to 600 bhp !!
-
A quick question, how long does it take to flash both the ECU/ gearbox for APR stage 1 & do VRS, within the price, offer the rolling road for and after HP/ torque?
-
Richard Guilliatt reacted to a post in a topic:
Car Insurance prices
-
Hi All, Had my renewal through from Privilege and was 25% more than last year! They want £432 now!! Anyway tried LV and £261 for Golf R & £283 for the wife’s S3 with a multi car policy. No mods as yet though other than black Prets. At that price I might get a quote for stage 1 map as warranty out in March.
-
You can also look at the rear shocks though the wheel and there is a connector sticking out at right angles with a cable attached. I was looking at mine the other day and noticed the extra metal piece welded to the main shock absorber body is rusting so sprayed with wax oil!. Rusting is probably from jet washing through the wheels though.
-
Mainframe reacted to a post in a topic:
Autowatch Ghost
-
It does come with stickers but defeating the point of "Ghost" as thieves will come prepared as Taz23-R mentioned. Ideally you would just give the thieves your the keys and then call the cops. Doubtful a perpetrator would come back into the house once found they could not start the vehicle as they would want a quick escape and may find you better prepared the second time! On another note, having issues with the iPhone app as you constantly have to open the phone even if the Ghost App is running in the background. If you try to start the vehicle and not disarmed then this will give an error with stop start although can be cleared with ignition on off. This will show an error in engine immobiliser module (engine blocked by immobiliser, VCDS scan. Also interesting is that in VCDS you can see an error in module 17 referring to an unauthorised module so this mist be the Ghost module? Only appeared after the install anyway. One downside to the device is servicing as I use to have mine collected which was around 10 miles away. The route uses 60 mph roads therefore the valet mode is not really useful as once it detects over 30 mph it will revert to armed on next start up meaning the service agent could not start he vehicle. I'm having to get a Saturday appointment this year.
-
GTI Clubsport S Brakes - worthwhile OEM+ Upgrade?
CAJPAJ replied to GrayMK7R's topic in Modifying your Golf R MK7
Worth noting that I believe, correct me if wrong, DS2500 pads are not technically street legal pads as no R90 approvals. Fine for track but if for some reason you had an incident on public roads related to brakes (if possibly proven somehow ) then insurance could be in question. Not so sure how easy it would be find pad types on examination though but you never know?