Jump to content

DCC shock absorber "misting"?


Recommended Posts

Hi Peeps,

 

I have a 2019 7.5 Estate with DCC and 83k miles (owned since 35k and 1.5 years old), and at its last service and MOT (by VW in UK) it was noted that one of the front shock absorbers was beginning to "mist" and this was a sign of impending failure, though they said it wasn't critical. They quoted around £550 - £600 to replace just the one.

 

When i bought the car I didn't know that it had had Racing Line lowering springs fitted to it.  It was a super hard ride and I subsequently hit a pothole and cracked one of the Pretoria's.  I opted to change the Racing Line springs out for Eibachs - as this was cheaper than finding oem VW springs to put back on, and still maintained a little lowering which i didn't mind aesthetically.  The suspension has always been a bit noisy, especially when on comfort mode, and don't know if this is normal. It's less noisy on Normal and Race modes.

 

I have only subsequently read about the DCC needing "resetting", on a lift with the wheels dangling - and don't know if this was done then the Racing Line Springs were originally fitted, and the people who fitted the Eibachs said they'd not heard of doing this - and they're a VAG performance tuning shop(!) so don't think this was done by them either (should i NOT go back there??).  Is this definitely a *real* thing?

 

I've never had the car with oem springs so don't know how the default ride is, and how much the DCC setting *should* change the ride feel.

 

• Is the misting indeed a sign of impending doom?

• Should I get VW to replace it?  

• Is replacing only 1 of them silly?  

• Is having the lowering springs fitted, and not necessarily having the DCC reset the probable cause of the early failure (and so the other three will need replacing soon also)? 

• Is 83k miles a reasonable length of time for the shocks to live?

• Are there non-VW options to consider (only if cheaper/betting with the existing Eibachs)?

 

It's a family car, not a track car, and gets mostly driven in DCC Comfort mode.  I love the car, but don't have money to throw at it for no good reason.  I can't justify to the wife spending money on purely aesthetic things like getting the rims redone (of boy do they need it!), or the paintwork fixed and ceramic coated etc.

 

Thoughts appreciated!

 

 

Link to comment
Share on other sites

Firstly I don't have DCC on my car and I don't know anything about a reset procedure with lowering springs though I am sure someone will be along who does. Mine is a 2019 Mk7.5 hatch though.

 

WRT the suspension in general, the misting you have reported, I had on a different car which first occurred after 3 years and they were still OK (as in passed MOT) after another 10 years so it may not indicate impending doom but at your mileage and on our roads the suspension (front in particular) will be starting to get tired. If you are planning on keeping the car I would certainly consider refreshing the suspension, especially as 2019 cars (at least the hatchback) seem to have more front suspension issues than might normally be expected. If yours has the alloy subframe too (see link at the bottom of this post) then that follows a pattern. I would get a VW specialist independent to do it rather than VW. 

 

VW original struts are made by Sachs, I believe, but you cannot buy an aftermarket Sachs branded replacement. However Bilstein (not Febi-Bilstein they are a completely different company) who are well regarded, produce an aftermarket replacement for the DCC unit which I believe to be this one which is quoted by Bilstein at 450 Euros each but can be had from Autodoc at £530 a pair (and I would replace both) which I would guess to be about half the price of a VW part, but worth checking. If the suspension is noisy (accepting you don't go into any detail about the noise) I would definitely replace the top mounts and bearings as the labour should be virtually the same as they are easily replaced when the strut is removed and they are not expensive (Bilstein make them too), I would also replace the roll bar drop-links (again inexpensive, often fail at higher mileages and hardly any more labour) and if you are 'all in' on this the lower suspension arm and ball joint too, though this is quite expensive and quite labour intensive especially if you have the alloy sub-frame. I would (and did) fit a Lemforder lower suspension arm rather than the VW part.

 

I think you will find the ride and noise massively improved after doing this if it is anything like mine.

 

If you have time and inclination it might be worth reading this. 

Link to comment
Share on other sites

@Julian N- Julian: Hi.

 

Jonathan has already provided lots of sage advice about this matter - but to add a bit more information to your specific questions:

 

Is the misting indeed a sign of impending doom?

The importance of the "misting" on the shock absorber is entirely determined by the amount. A minor oil-film on the piston-rod of the shock absorber is normal. However, a "wet" rod IS a sign of a leaking seal and it is recommended practice to replace the strut. Of course, make sure that the oil is not coming from another source - like a hydraulic pipe/hose.

 

Should I get VW to replace it?

Hmm.... not sure how stuff works up there in the land of King Chuck - but my experience is that VW dealers charge like a wounded bull to simply pick-up a spanner!! That said, the DCC system is a proprietary product - so some level of expertise is needed to integrate the replacement shock absorber into the DCC system- but it ain't rocket science!! My advice is to get a quote from a local "indy" (independent) workshop first 

 

Is replacing only 1 of them silly?

Absolutely NOT!! It really depends on what has caused the leaky seal. Fact is that the individual struts on the car experience very different stresses in their life cycles - so these types of problems often affect only one strut.

 

Is having the lowering springs fitted, and not necessarily having the DCC reset the probable cause of the early failure...?

The purpose of the "Basic Setting procedure" following a major change to the DCC system is to establish a new "neutral position"  for the altered suspension geometry. This set-point is recorded in the module that's responsible for operating DCC and a condition of the Basic Setting procedure is to lift the car so that all 4 x wheels are off the ground (meaning the suspension is fully extended). So, it's a kind-of calibration procedure that's individual for each new suspension arrangement!

I very much doubt that not completing the Basic Setting procedure would contribute to this problem - it's more likely that the omission (if indeed it was omitted) would result in poor DCC operation, rather than outright failure of the oil seal on ONE strut. But I'm guessing!!

 

Is 83k miles a reasonable length of time for the shocks to live?

It's like the longevity of us carbon based life units - ALL the sins of our youth are brought to account in older age and we pay a high price for stuff that we previously believed to be unimportant !!

I don't work in miles (we call these imperial-units "bananas" down here) - but that's about 134,000 kms. If this car has had a hard suspension life from the previous owner - then it ain't unreasonable that the DCC system needs attention now. This is especially so because there probably was a very good reason why the original owner threw money at modifying the factory DCC set-up (which was likely related to the way the car was driven).

 

Are there non-VW options to consider (only if cheaper/betting with the existing Eibachs)?

It is possible to delete DCC entirely - but it involves coding (in addition to the fitment of standard struts). I have no idea of the related cost up there in UK if you don't DIY the project

 

Don

 

 

 

 

Link to comment
Share on other sites

Thanks Jonathan and Don.

 

VW themselves weren't pushing the replacement of the strut quite yet, and they ARE kinda pushy, so i'm going to read into that, that this is not urgent.  I'll get a quote from a non-VW place, but might not do anything about it right now.  When i do, i'll just do the one, if that's all that's needed (thanks Don).  I'll look into whether the top mounts, bearings, and drop links need/should be done at the same time (thanks Jonathan)

 

Unfortunately I don't know if the DCC is operating as it should because I have no standard car to compare it to.  But i think i'm going to carry on with "it's fine for now".  

 

One "conceptual" question i do still have though, is this:  

When you put lowering springs on, they're shorter than the standard ones, and the travel of the shock is not adjusted (unless maybe you have coilers, but i'm still not sure about that.)  So, when VW first noted that the springs were not OEM, they said they move around by hand when the car is on a lift - ie no longer tight as we've removed 10 - 30mm of spring. Nothing is done to change/reduce the travel length of the strut, right?

 

What I don't get, is that if you zero out the DCC when it's on a lift, aren't the wheels going to dangle to their maximum regardless of whether you have standard springs or super duper low/short ones, or even no springs?  Surely the car can only register the/any new different spring/ride height when its set on the ground, no??  🧐  I've never gotten my hands dirty with suspension though, so i'm maybe missing something...

 

 

Link to comment
Share on other sites

@Julian N: Excellent question! I'm not sure that it provides an answer - but I suggest that you read VW's "Self Study Program 406".

 

It's an explanation regarding how DCC works - you can find a copy of the SSP  HERE

 

Don 

Link to comment
Share on other sites

The standard DCC struts are Monroe on all the 7.5 i have seen. they are easily obtainable for around £150 each for the likes of GSF. Just replace at this age/mileage and be done with it, do top mounts at the same time. Last one i replaced dcc struts on was 32k miles and they were shagged. 

Link to comment
Share on other sites

On 16/05/2026 at 00:00, Sequence said:

The standard DCC struts are Monroe on all the 7.5 i have seen

Thanks for the clarification, the non-DCC struts on mine were labelled ZF and iirc correctly marked SACHS, so I assumed (dangerous I know) that the DCC dampers were the same.

Link to comment
Share on other sites

Thanks for the feedback.  @Sequence , how can one tell whether the struts are "shagged" exactly?  Back in the day, you'd push down on a corner of the car and it'd bounce back, but not keep on bouncing, from my limited recollection - if it bounced a few times, they were shagged, right?  What do they do these days, with them still on the car, to test this?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...